Products Page

1 Pairs 45A 3.5mm Male Female Banana Connector

Quantity

Price: $1.00

Loading Updating cart…

2 Layer 20cm*20cm max 10pcs

This service provides more PCB dimensions(include 5cm x 15cm,5cm x 20cm,10cm x 15cm,10cm x 20cm,15cm x 15cm,15cm x 20cm,20cm x 20cm ) for you. And you can select 5pcs or 10 pcs PCBs. If your PCB have smaller size such as 5cmX5cm or 10 cm X10cm another more cheap service ‘ 2 Layer 10cm*10cm max -10pcs’ may suitable for you. The ‘ 2 Layer 20cm*20cm max-50pcs’ service will provide you 50pcs PCBs.Please check the price for different service and find the most economic one.

Fusion PCB Order Steps:

Purchase fusion PCB Service from online store and check out.
An order number will be provided in confirmation email from us.
Send the gerber file to our email. The gerber files must be packed into a zip or rar file and named Order(your order number)_(PCB size). For example: Order100_10x10.rar.
If the file and design meets requirements, they will be processed and shipped in 4-6 days.

Gerber file requirement:(The following layers are needed)
Top layer: pcbname.GTL
Bottom layer: pcbname.GBL
Solder Stop Mask top: pcbname.GTS
Solder Stop Mask Bottom: pcbname.GBS
Silk Top: pcbname.GTO
Silk Bottom: pcbname.GBO
NC Drill: pcbname.TXT

Note:

Board outline must be included at least in one layer.
The Gerber file must be RS-274x format.

Quantity

Price: $18.00

Loading Updating cart…

2 Layer 20cm*20cm max 5pcs

This service provides more PCB dimensions(include 5cm x 15cm,5cm x 20cm,10cm x 15cm,10cm x 20cm,15cm x 15cm,15cm x 20cm,20cm x 20cm ) for you. And you can select 5pcs or 10 pcs PCBs. If your PCB have smaller size such as 5cmX5cm or 10 cm X10cm another more cheap service ‘ 2 Layer 10cm*10cm max -10pcs’ may suitable for you. The ‘ 2 Layer 20cm*20cm max-50pcs’ service will provide you 50pcs PCBs.Please check the price for different service and find the most economic one.

Fusion PCB Order Steps:

Purchase fusion PCB Service from online store and check out.
An order number will be provided in confirmation email from us.
Send the gerber file to our email. The gerber files must be packed into a zip or rar file and named Order(your order number)_(PCB size). For example: Order100_10x10.rar.
If the file and design meets requirements, they will be processed and shipped in 4-6 days.

Gerber file requirement:(The following layers are needed)
Top layer: pcbname.GTL
Bottom layer: pcbname.GBL
Solder Stop Mask top: pcbname.GTS
Solder Stop Mask Bottom: pcbname.GBS
Silk Top: pcbname.GTO
Silk Bottom: pcbname.GBO
NC Drill: pcbname.TXT

Note:

Board outline must be included at least in one layer.
The Gerber file must be RS-274x format.

Quantity

Price: $12.00

Loading Updating cart…

2.4″ TFT LCD: TFT01-2.4SP

TFT LCD module has always been one of the hot products in DIY industry and LCD is basically the necessary products during all projects, at the same time, serial port modules are also the popular ones, because it takes few IO and the usage is simple. This section of the 2.4S-inch TFT LCD serial SPI integrated features of compact, SPI interface, fully compatible with popular LCD5110 interface cable sequence, and will replace the increasingly reducing LCD5110.

Feature:

TFT01_2.4 SP is a 2.4 “SPI TFT LCD Screen Module, 10pins interface, compatible LCD5110 interface. Not just a LCD break but include SD card (2GB),
The LCD in the TFT01 is ILI9341. It’s a 240 * 320 (resolution), 2.4S inch TFT LCD screen.The LCD has a wide viewing angle, the contrast is also very suitable.
The display interface is serial, it just needs 5 wires (CS, RS, SCL, SDA, RST) for controlling.
Replace LCD5110, Support direct plug in ElecFreaks Joystick shield, EFCom, Key Pad Shield etc
SDcard use hardware SPI interface (CS / MOSI / MISO / SCK), Not solder pins.

Parameter:

SDO: Serial clock output
LED: 3.3V IO and Power Supply pin
SCL: Serial clock input
SDA / SDI: Serial data input
DC: Data / Command selection
RST: Reset, Low level active
CS: Chip Selection, Low level active
GND: Ground
VDD33: 3.3V Power Supply pin
UTFT Support

Quantity

Price: $21.00

Loading Updating cart…

6 Channel Radio Set

Parameter:

model name:6 channels transmitters
model no:FS-CT6X
channels:6 channels
mode type:airp;ame, helicopter, glider
stick mode:left hand or right hand
modulation:frequency modulation
module frequency:35mhz,40mhz,72mhz,2.4chz
antenna length:115cm/26mm
code type:ppm/gfsk
power:12 vdc
RF power:less than 0.8w
weight:575 grams
size:189*72*218mm

Features:

6 channels output
any model memory
computer program
USB soket
4 type( airplane HELI90 HELI120 HELI140)
4 models select

Quantity

Price: $82.00

Loading Updating cart…

LION 11.1V 2200MAH 30C Lithium Battery

Parameters:

  • Product Type: Rechargeable lithium polymer battery
  • Battery Type: LION Power 11.1V 2200MAH 30C beast series
  • Battery capacity: 2200mAh
  • Continuous Discharge Rate: 30C
  • Size & Weight: 108mm x 34mm x 23mm
  • Plug Type: T plug, plug the balance charge
  • Charging way: the need to balance recharge your with charging current 0.5-1A
Quantity

Price: $44.00

Loading Updating cart…

Quadcopter 30A ESC

Parameters:

Output capacity: Continuous current 30A, short-time current 40A (less than 10 seconds);
Power input: 5.6V – 16.8V (2-4 lithium battery pack or Section 5-12 NiMH / NiCd battery pack);
BEC output: linear regulator mode, 2A
Maximum speed: 2-pole motors 210 000 r / min, 6-pole motor 70 000 rev / min, 12 pole motor 35 000 rev / min;
Size: 45mm * 24mm * 11mm

Quantity

Price: $18.00

Loading Updating cart…

Quadcopter reverse paddle * 2

Parameters:

Positive and negative clover paddle: GWS 8040 9050
Multi-axis / axis fixed wing
Special three-blade propeller

  • Positive pulp + Anti paddle (one pair)
Quantity

Price: $9.00

Loading Updating cart…

Raspberry Pi B GPIO Ref Board

L * W: 46*19mm
Double-side compatible with Raspberry Pi and Raspberry Pi Model B.
Able to be inserted directly to the GPIO port of Raspberry Pi Model B, in which case, the pin assignment of the GPIO port is clearly visible.
DuPont lines can be plugged additionally, without any impact on the experiment.

Quantity

Price: $5.00

Loading Updating cart…

Raspberry pi Expansion Board

Features:

This board is produced using immersion gold (ENIG) production process. All ENIG hole spacing, are standard 2.54mm (100ml). The IC, compatible with DIP packaging, is soldered directly to the upper end for prototyping experiments.
The extended IO port can be directly inserted into the female header connector via bread lines, as such, greatly improving using easiness and providing the platform for speed implement of your innovation on the prototype extended board.
IO port is with terminal output. When connecting an external module, you can put on a wire and tighten it. The IO port is for Raspberry Pi and external module layouts and links.
Raspberry is hard to support due to the large gap between the board components. This board, however, uses custom female header connector and silicone pad as a prototype board support.

Quantity

Price: $12.00

Loading Updating cart…